3334SS-4003

Unitized stainless steel base, tables, leg bolt levelers, carriage channel & supports, Aluminum head and door, removable

Std. = Standard    EC = Extra Cost    TE = Totally Enclosed    TEFC = Totally Enclosed Fan Cooled

Two saw blades • Operation and Safety manual • Safety wall poster • Safety end cut pusher plate

Watertight magnetic, thermal overload and under voltage protection

Aluminum: removable head • removable door

Unitized welded, Stainless steel

124” (3150mm) L x 5/8” (16mm) W x .022 (0.56mm) thick, 3 teeth per inch, hard tooth, (two supplied with each saw)

Upper and lower blade back up guide assemblies with carbide long-life inserts, each removable as an assembly

Ratchet arm and cam against pound tested spring and tension spring gauge

16” (40.64cm) single flange, cast iron, nickel plating, upper wheel assembly removable

Heavy duty tapered roller bearings used in upper wheel hub and lower bearing housing

Poly Pan, rounded corners, sealed off from other parts of base, accessible through hinged door

Stainless steel body, long-life carbide guide inserts, steel saw cleaners, removable as a unit for easy cleaning (assembly also adjustable as a unit)

Non-slip silent v-belt, tension adjustable

Stainless steel leg bolt levelers

Larger stainless steel 8-bearings E-Z flow carriage 17-1/2 (444 mm)W x 25-9/16” (649 mm)L

Stainless steel faced, adjustable from 1/16” (1.6mm) to 6-1/2” (165mm), Locks in position, easy to adjust, entire assembly removable for cleaning

Sealed off from meat contact areas, easily accessible through removable panel door

Held in place with two stainless steel push-pull hold down latches

Safety end cut pusher plate and safety pusher plate storage hanger are supplied as standard equipment

Stainless steel movable head and door (IPOS) • Double saw guide bar • Stainless steel stationary bar (IPOS) • Full length S.S. front stationary table (IPOS) (see drwg. 2) • Meat gauge extended 6” (152mm) past blade (IPOS) (one stabilizer req.) • Cast plated single flange lower removable saw blade wheel (IPOS) • Cast plated double flange (upper & lower) saw blade wheels (IPOS), NOTE: lower saw wheel not removable • Cast plated double flange (upper & lower) removable saw blade wheels (IPOS) • S.S. single flange (upper and lower) saw blade wheels (IPOS), NOTE: lower wheel not removable • S.S. single flange (upper and lower) removable saw blade wheels (IPOS) • Front table extension 14-3/4” (375mm) x 15-3/4” (400mm) • 3 wire (1 ph.) or 4 wire (3 ph.) 12 ga. Cord less plug (specify length) • Narrow blade guides (for thin blades) • Split rear stationary platter (fast blade change) (IPOS) • Standard length legs with 2-1/4” (57.2mm) disc floor pads (IPOS) • Longer S.S. hex legs to raise work surface ht. (ck w/rep.) (IPOS) • Drwg. I. Md 3334SS-TL – True left-hand feed, movable S.S. head and door, less thickness gauge plate • Drwg. 2. Md 3334SS – Trim saw – right to left feed, stationary front table, optional meat gauge assembly • Drwg. 3. Md 3334SS-TL – Trim saw – True left to right feed, stationary front table, movable S.S. head and door, less meat gauge assembly • Drwg. 4. Md 3334SS-4003-PC – Portion control – Std. right to left feed movable S.S. head and door, micro gauge fence. Movable S.S. head • Drwg. 5. Md 3334SS-4003LP-PC – Portion control – Std. right to left feed, movable low profile S.S. head, special meat thickness gauge plate • Waterjet blade cleaning system (check w/Rep.) S.S.=Stainless Steel    IPOS=in place of standard   drwg.=drawing     ga.=gauge    EC=extra cost    NC=no charge

Higher feet per minute saw blade speed (call your Representative)

U.L. • N.S.F. • U.S.D.A. • C.S.A. • C.F.I.A.

Uncreated: 510 lbs. (231kg)   Crated: 564 lbs. (256kg)